產品名稱: ASKER橡膠硬度計
產品型號: D
產品展商: 上海騰明工貿有限公司
關注指數:27
產品文檔: 無相關文檔

簡單介紹 ASKER橡膠硬度計測量硬度的基本因素之一是確定不同橡膠、人造橡膠及塑料制品的特性。適合特點的設計。所有的硬度計的生產及校準都是在人員的嚴格控制下進行的，可以保證并符合國內及國際標準.代理日本高分子ASKER橡膠硬度計中國總代理.產品庫存量大.技術全面.提供五年質量保證及所有零配件及維修服務

ASKER橡膠硬度計的詳細介紹

ASKER橡膠硬度計測量硬度的基本因素之一是確定不同橡膠、人造橡膠及塑料制品的特性。適合特點的設計。所有的硬度計的生產及校準都是在人員的嚴格控制下進行的，可以保證并符合國內及國際標準.代理日本高分子ASKER橡膠硬度計中國總代理.產品庫存量大.技術全面.提供五年質量保證及所有零配件及維修服務.ASKER橡膠硬度計

ASKERDurometer Type DASKER橡膠硬度計

The Type D Durometer forhard rubber (high hardness) and plasticsASKER橡膠硬度計 Used world-wide for measuring hard rubbers and plastics, andspecified in the standards of JIS K 6253, ASTM D 2240, ISO 7619,DIN53505, etc.

Features

Indentor

Height: 2.50mm Shape: Sharp ConePoint

Pressure foot

The Pressure foot in contact with thespecimen is 44mm in width and 18mm in depth, wide enough to ensureaccurate measurement. Another type of durometer with an 18mm diameter pressure foot isavailable. In addition, the Longer Pressure Foot Type (DL Type) isapplicable for measurement of narrow or concave specimens .

Hardness TesterSelection Chart Our product line consists of varioustypes of durometers applicable to specific materials as indicated in the chart above. Type A Durometer (ASKER A type), conforming to JIS K 6235 is themost popular type of durometer for measuring rubber hardness. However, verification is recommended because a significantdifference is estimated to be the largest when a durometerindicates measurement values from 10 to 90 points. For hard specimens for which Type A Durometer readings indicatemore than 90 points, measurements should be undertaken using theType D Durometer (ASKER D type). However, for soft specimens withmeasurements of less than 20 points, the ASKER C type or Type EDurometer (ASKER E type) should be used. The most importantconsideration in using durometers is to select the correct type forpurposes of measurement according to the specimen.

Specification

Standards JIS K 6253 JIS K 7215 ASTM D 2240 ISO 7619 ISO 868 DIN 53505 Indicationrange 0 point - 100 point (262 degree dialscale) Minimumindication 1 point (Accuracy : ±1 point) Indentor Design(mm) Height: 2.50 30°Angle Sharp Cone Point Tip Radius0.1 Spring Forces[mN(g)] 0 point: 0(0) 100 point: 44500(4538) Central hole ofdiameter of Pressure foot Φ3 Pressurefoot Dimension (mm) 44×18(Rectangular) Outer Dimension(mm) Approx. Width 57×Depth 30×Height 76 Weight(g) 200 Application hard rubber, plastic

Outer Dimension(mm)

A custom designed pressure foot durometer is availableaccording to specimen conditions.

Option

Two-pointer type (max-hand andactive hand) of Rubber Hardness Tester The stationary set hand (max-hand) makes the maximum value easierto read and allows the creep characteristics of a specimen. Accurate measurement is made possible for specimens* for whichstress relaxation occurs over time or for specimens for which it isdifficult to take readings from the front. *Materials for which the reading decreases immediately after theindentor has been pressed against the surface.   Constant Loader forDurometer · Constant loarder assures uniform test pressure eliminatingfalse readings due to differences between operators in measuring byhand. · High accuracy and repeatability of the hardness readings areassured by the flexible joint function.   Indentor ExtensionTester · The gauge to check the indentor height on a durometer and thereading indicator mechanism. · Inspection is conducted at 2, 50, and 100 pointsrespectively.   Load Tester forHardness Tester · Tester to check load properties of the spring on a durometer · Inspection is conducted at 2, 50, and 75 pointsrespectively.

上海騰明工貿有限公司 原裝進口各類精密儀器
https://www.tmdprecise.cn  DET: