低溫試驗箱使用說明書
一、低溫試驗箱用途與特點：
1、本儀器使用于水泥、混凝土、各種水卷材、型材、塑材的低溫檢測。
2、本儀器由壓縮機、冷凝器、過濾器、毛細管、蒸發器、恒溫槽、數顯儀表、數碼控溫系統等組成。本機制冷速度快、噪音小，使用方便。
二、低溫試驗箱技術參數：
1、本儀器容積：160L
2、控溫范圍：0℃—-40℃
3、控制：&plun;0.5℃
4、電源：AC220V、50HZ
5、環境溫度：0—23℃
6、相對濕度：≤75%
三、低溫試驗箱結構特點：
該儀器選用上翻蓋兒，對低溫保持，試驗方便。恒溫槽采用腐性較強的合金板，外用優質鋼板制作，中間充聚胺脂保溫材料。
四、低溫試驗箱操作使用：
開箱后檢查儀器是否完好，然后把儀器放置在水平面上。
檢查電源是否穩定，然后插上電源，打開電源開關，此時儀表顯示為恒溫槽內實際溫度，等3分鐘后，壓縮機啟動。
五、低溫試驗箱溫度設定：
按住“▲”鍵或下“▼”鍵3秒，顯示“5P”與設定溫度，再按“▲”鍵或“▼”鍵調整設定溫度，調整好后，不要按任何鍵，10秒鐘后自動保存退出。
六、低溫試驗箱溫度事項：
1、儀器不允許在有潮濕及腐蝕性氣體的環境中存放與使用。
2、次使用（長時間未用情況下）本機須工作2小時后方能作檢測，以免次使用數值不準確。
3、由于某些原因斷電或停電，就立即關掉電源開關，若需要重新啟動，須間隔30分鐘以上方能開機使用，以免開機燒毀壓縮機。
4、在搬運時嚴禁將儀器傾斜45°以上。
5、使用時需要穩壓器調節：220V 50Hz 15A 接地。
6、本儀器須接地。
7、本儀器只可用于實驗室用，不可作普通冰柜使用，否則不予保修。
8、嚴禁在不使用時長時間運行。
9、本儀器經長途運輸或搬運，靜置2小時以后方能使用。
七、低溫試驗箱裝箱清單：
使用說明書一份、合格證一份。
更多與 產品相關歡迎您來電咨詢
Low temperature tt chamber operating instructions
A and low temperature tt chamber US and featur:
1, the instrument used in cement, concrete, waterproofing materials, shaped materials, plastic material of low temperature tt.
2, the instrument by the import comprsor and condenser, filters, capillary and evaporator, constant temperature trough, dial display instrument, dial temperature control system, etc. The machine cooling speed, low noise, the use of reliable and convenient.
Second, the low temperature tt chamber technology parameters:
1, the instrument volume: 160 l
2, temperature control range: 0 ℃ - 40 ℃
3, control accuracy, plus or minus 0.5 ℃
4, power supply: AC220V, 50 hz
5, environmental temperature: 0-23 ℃
6, relative humidity: 75% or ls
Three, the low temperature tt chamber structure featur:
Flip on the instrument selection, to keep low temperature effect is good, easy to tt. Thermostat adopts anticorrosion stronger alloy plate, external use of high qualified steel plate production, filling polyurethane thermal insulation material in the middle.
Four, low temperature tt chamber operation:
When unpacking the case inspection instruments are in good condition, and then placed the instrument in the horizontal plane.
Check whether the power supply is stable, then plugged in, turned on the power switch, instrument display at this time for the actual temperature in constant temperature trough, after 3 minut, the comprsor start.
Five, the low temperature tt chamber temperature setting:
Hold "bring" key or "▼" key for 3 seconds, the display "5 p" and the set temperature, and then prs "bring" or "▼" key to adjust the set temperature, adjust good, do not prs any key to automatically save out after 10 seconds.
Six, low temperature tt chamber temperature items:
1, the instruments are not allowed in damp and store in the environment of corrosive gas and use it.
2, for the first time use (for a long time without use) the machine must work to 2 hours before tting, so as to avoid using numerical inaccuracy for the first time.
3, for some reason or power blackouts, immediately turn off the power switch, if you need to rtart the, must wait 30 minut to boot using, so as to avoid sharp boot burn down comprsor.
4, in handling, the instrument are forbidden to tilt more than 45 °.
5, the need when using voltage regulator to adjust: 15 a 220 v, 50 hz grounding.
6, the instrument must be grounded.
7, the instrument can be used in laboratory tts only and cannot be used as ordinary freezers, otherwise no warranty.
8, it is strictly prohibited without using long time running.
9, the instrument by long-distance transportation or handling, let stand for 2 hours, can use.
Seven, low temperature tt box packing list:
One copy of instruction manual, a certificate of approval.
More products related to welcome you to inquire