詢價
原裝供應ATOS減壓閥,阿托斯減壓閥樣本
ATOS直動式減壓閥通常與雙作用氣動執行機構配套使用，兩位是兩個位置可控：
開-關，五通是有五個通道通氣，其中1個與氣源連接，兩個與雙作用氣缸的外部氣室的進出氣口連接，
而注脂流量控制閥壓力過高，
Two with the internal air chamber of the inlet and outlet,
the specific working principle can refer to the double acting
pneumatic actuator working principle in the gas (or liquid)
Two three-way solenoid valve has an inlet (access air source),
1 out of the hole (available to the target device gas source),
兩位三通電磁閥具有1個進氣孔(接進氣氣源)、
1個出氣孔(提供給目標設備氣源)、1個排氣孔(一般安裝一個，如果不怕噪音的話也可以不裝
減壓閥常忽略壓力問題。在注脂操作時，注脂壓力有規半自由浮球式蒸汽疏水閥律地呈峰谷變化。
壓力過低，密封漏或安全閥失效,壓力過高，
注脂口閥門制造商堵塞、密封內脂類硬化或密封圈與閥球、閥板抱死。
通常注脂壓力過低時，注入的潤滑脂多流入閥腔底部，一般發生在小型閘閥。
a vent (generally installed one, if not afraid of noise, then you can not install
Pressure relief valve often ignore the pressure problem.
ATOS直減壓閥工作原理：ATOS直動式減壓閥通常與單作用氣動執行機構配套使用，兩位是兩個位置可控：
開-關，三通是有三個通道通氣，一般情況下1個通道與氣源連接，
另外兩個通道1個與執行機構的進氣口連接，1個與執行機構排氣口連接，
seal the lipid hardening or sealing ring with the valve ball, the valve plate is locked.
Usually grease pressure is too low, the injection of
grease into the bottom of the valve cavity, generally occurs in the small gate valve.
具體的工作原理可以參照單作用氣動執行機構的工作原理圖。
兩個與內部氣室的進出氣口接連，具體的工作原理可參照雙作用氣動執行機構工作原理 在氣路(或液路)上來說，
In the grease injection operation, the pressure of the grease is controlled by the semi-free float steam trap.
Pressure is too low, seal leakage or safety valve failure, the pressure is too high,
Grease the mouth of the valve manufacturer to block,
原裝供應ATOS減壓閥,阿托斯減壓閥樣本
