2 Screw,The Take-0ut Robot with 1 Station Cooling ,Only 14S.

Demark 12,24 cavities wide mouth/jar pet preform injeion moulding machines@(pet preform injeion molding systems@pet preform injeion mulding plant@) uses a new part cooling and robot handling system, which features:
    1.  Cooling on the inner surface of the preform without using compressed air, unlike most post-mold cooling systems which only cool the outer surface
    2.  Optimized cycle utilization — being mounted on the moving platen, the cooling system remains aive for up to 85% of the overall cycle.

Demark pet preform injeion moulding machines are available from 280 to 500 tonnes (2800 to5000 kN) and up to 96 cavities.

Demark pet injeion moulding machines offer:
    1.  Faster cycles(14s)
    2.  Reduced energy consumption
    3.  aller footprint 
    4.  Improved repeatability 
    5.  Rapid set-up

Features:
    1.  Two state plasticizing enables plenty injeion quantity;
    2.  Take out plate with three working position insures sufficient cooling time and shorter cycle time;
    3.  High quality parts and accessories from world famous brands enable higher speed and precision;
    4.  Special screw design increases torque while brings down shear force to avoid degradation;
    5.  Accumulator from world reputable manufaure increases performance while brings down power consumption;

Reflex Platens
Reflex platens distribute clamp force evenly across the platen face.
Reflex platens:
    1.  Allow for 10-30% lower clamp tonnage 
    2.  Decrease mold wear 
    3.  Improve part quality
 
Injeion Units
demark systems offer both reciprocating screw (RS) and two-stage injeion units. RS units offer the performance required for many PET applications while two-stage is appropriate for higher throughput applications.
 
Controls
DMK-based controls manage all funions of our PET produion systems, with optional packages to integrate auxiliaries and downstream part handling equipment. Advantages include:
    1.  Faster cycle times 
    2.  Improved shot-to-shot repeatability 
    3.  Remote conneivity through ServiceNetLink 
    4.  Control of molding system and auxiliaries from a single interface
 
Linear Bearings
Linear bearings support the moving platen direly on the machine base. This design reduces mold wear by improving platen alignment and perpendicularity, and provides a grease free molding environment.

Technical Parameter:

ITEM		UNIT	DMK-PET12-Wide	DMK-PET24-Wide
INJEION UNIT	Screw L/D Ratio	L/D	25	25
	Screw Diameter	mm	100	120
	Injeion Pressure	Kgf/cm2	875	875
	Output(Max)	Pcs/h	17000	17000
	Theory Shot Volume(Max)	cm	2850	3800
	Shot Weight(PS)	g	3420	4560
		ozs	121	161
CLAMPING UNIT	Clamping Force	T	360	360
	Clamping Stroke	mm	645	645
	Max/Min Thickness of Mould	mm	300~700	300~720
	Space Between Tie Bars (WxH)	mm	660~860	660~860
	Ejeor Stroke	mm	180	180
	Ejeor Force	T	12	12
	.of Ejeor Pins	PCS	5	5
	Max Pressure of System	Kg/cm2	140	140
MOULD&ROBOT	Cavity(Max)	PCS	48	48
	Neck of Bottle(Max)	mm	42	42
	Length of Preform(Max)	mm	190	109
	Weight of Preform(Max)	g	35	50
	Te of Mould	Needle Valve of -Cutting PET Preform Molds
	Manipulator	Cavity	48x3	48x3
	Cooling Form	Cavity	144	144
POWER UNIT	Pump Motor Power	KW	25	25
	Robot Power	KW	25	25
	Mould Heater Capacity	KW	48	48
	Heater Input Capacity	KW	71	71
	Total Power	KW	264	264
OTHER	Eleric Power Supply(3-phase AC)	V/HZ	380/50	380/50
	Chilling Water	℃	5~15	5~15
		Mpa	0.6	0.6
		L/min	600	600
	Coolling Water	℃	30~55	30~55
		Mpa	0.25	0.25
		L/min	200	200
	Compressed Air	Mpa	0.7~0.9	0.7~0.9
		L/min	800	800
	Machine Size (LxWxH)	mm	8455x3884x2230	8455x3884x2230