并已取得工業品生產許可證、生產許可證、?；飞a(chǎn)許可證等生產資質。
歡迎您的來電咨詢訂購，固定電話： 手機：
在線咨詢
安裝說明：
Installation instructions:
1先確認與摩托車相適配的蓄電池型號，核實與所換購電池型號是否一致。（check with a motorcycle battery adapted models , check with the redemption of the battery models are consistent.）
2確認電解液與之匹配的電池型號是否一致，且須閱讀附在電池上的使用說明書。（Make sure the battery electrolyte matching model is consistent, and must read the instruction manual attached to the battery.）
3撕下電池注液孔上密封膠帶或打開注液孔上的液孔栓及排氣嘴上之膠套。（Remove the battery injection hole sealing tape or liquid and pouches exhaust bolt hole injection hole on the lip of the opening .）
4 A：摘掉電解液瓶密封壓條（備用）使液瓶口對準電池注液孔，用力壓下電解液瓶，插破密封薄膜，將瓶?jī)?nèi)電解液注入。之后用力將密封壓條壓入電池注液孔。（A: remove the electrolyte bottle sealing bead ( spare ) battery align the liquid bottle injection hole , hard pressed electrolyte bottles, broken plug sealing film , the bottle is completely injected into the electrolyte . After sealing bead firmly pressed into the cell injection hole .）
B：剪去電解液瓶蓋上的尖銳部份，套上膠管，膠管的另一端電池的注液孔，將瓶?jī)?nèi)的電解液緩緩注入電池中，注入量以平行電池上印刷的水位線（UPPER LEVEL線）為適宜。（B: sharp cut on the cap part of the electrolyte solution , put the hose , the hose is inserted into the other end of the injection hole of the battery, the electrolyte solution bottle slowly injected into the cell , the battery parallel to the injection amount of the maximum printed water line (UPPER LEVEL line ) as appropriate.）
5將電解液注入后，電池應靜止20~30分鐘后使用。（After full inject electrolyte , the battery should rest for 20 to 30 minutes before use .）
6檢查摩托車上的電池固定震架、及電池端子性方向和接線位置關系后正確安裝電池。接線時要注意正負性，如果接反可能導致燒壞摩托車的電器部件。（When the battery is fixed shock mount six checks on a motorcycle , and the battery terminals and wiring polarity positional relationship between the battery is installed correctly. Be sure to pay attention to the polarity when wiring , if reversed could lead to burnout motorcycle electrical parts.）
7如果遇到摩托車起動點火欠佳時：有可能產品在保管中曾有過不當之處或是加液后化學反應時間不夠所導致蓄電池干荷性能略有降低，此情況下補充電即可恢復性能，恢復后的性能和壽命亦不會受到影響，可以。（If you experience poor motorcycle ignition starter : There may be in custody after the product had been inappropriate , or not enough time plus liquid chemical reaction caused by dry-charged battery performance is slightly lower , in this case just add power to restore performance , performance and life after recovery will not be affected , you can rest ured that use .）
日常保養（Routine maintenance）：
1表面污垢用清水清洗后干燥，請勿使用沾有汽油等油類的抹布。
（A surface dirt with water after cleaning and drying , do not use gasoline and other oil rag moistened .）
2注液孔周圍有電解液漏跡時，檢查液孔密封壓條或液孔栓是否吻合和擰緊。
（Around 2 electrolyte leakage injection hole track , check the hydraulic fluid seal the hole or holes layering is consistent and tighten the bolt .）
3端子易被氧化腐蝕，從而影響充放電效果，需經常清理和在端子涂上凡士林或牛油。
（ terminals susceptible to oxidation corrosion, thus affecting the charge-discharge effect , need regular cleaning and terminals Vaseline or butter .
4經常檢查并保持電池的液面線（免維護電池除外）、固定架，電池松動而發生正負性短路。
（regularly check and maintain the highest level of the battery line ( except maintenance-free batteries ) , holder, to prevent loose battery positive and negative polarity short circuit occurs .）
